Gridfinity-compatible baseplate and bins
========================================

A 4 x 3 baseplate (168 x 126 mm) and a set of bins that fill it exactly:

  gridfinity-baseplate-4x3.stl     4 x 3 baseplate, thin style, no magnet holes. Print 1.
  gridfinity-bin-2x2-6u-2div.stl   2 x 2 bin, 6 units high (46 mm with lip), two compartments. Print 1.
  gridfinity-bin-2x1-3u-tab.stl    2 x 1 bin, 3 units high (25 mm with lip), label tab and scoop. Print 1.
  gridfinity-bin-2x1-3u-2div.stl   2 x 1 bin, 3 units high, two compartments, no tab. Print 1.
  gridfinity-bin-1x1-3u.stl        1 x 1 bin, 3 units high, label tab and scoop. Print 4.

The STLs are in print orientation (flat on the bed), in millimetres.

Gridfinity numbers
------------------
Grid: 42 x 42 mm per unit. A bin's footprint is 41.5 mm per unit (0.5 mm clearance).
Height unit: 7 mm. A bin of n units is 7 x n mm tall plus a stacking lip
(nominally 4.4 mm): 2u = 18.4 mm, 3u = 25.4 mm, 6u = 46.4 mm nominal.
This generator rounds the top of the lip, so the printed bins measure
about 0.85 mm less (24.5 mm and 45.5 mm); stacking is unaffected.
The thin baseplate is 5 mm tall and open underneath.
Bins print without supports; no magnets or screws are used in this set.

Settings used
-------------
Baseplate (gridfinity-rebuilt-baseplate.scad):
  gridx=4 gridy=3 style_plate=0 (thin) enable_magnet=false
Bins (gridfinity-rebuilt-bins.scad), all with refined_holes=false, magnet_holes=false,
screw_holes=false (plain bottoms):
  2x2: gridx=2 gridy=2 gridz=6 divx=2 divy=1
  2x1 with tab: gridx=2 gridy=1 gridz=3 (default tab and scoop)
  2x1 split: gridx=2 gridy=1 gridz=3 divx=2 style_tab=5 (no tab)
  1x1: gridx=1 gridy=1 gridz=3 (default tab and scoop)

Making other sizes
------------------
Every piece here was made with gridfinity-rebuilt-openscad:
  https://github.com/kennetek/gridfinity-rebuilt-openscad
Open gridfinity-rebuilt-baseplate.scad or gridfinity-rebuilt-bins.scad in OpenSCAD
(a recent development snapshot renders much faster), open the Customizer, change
gridx / gridy (units of 42 mm) and gridz (units of 7 mm), press F6, then export STL.
To fit a drawer, set the baseplate's distancex / distancey in mm and it pads the
edges. From the command line:
  openscad -o bin.stl -D gridx=3 -D gridy=2 -D gridz=6 gridfinity-rebuilt-bins.scad

Gridfinity
----------
Gridfinity is the modular storage standard created by Zack Freedman.
These parts are Gridfinity-compatible; CadFlow is not affiliated with
Zack Freedman or Voidstar Lab.

Attribution and licence
-----------------------
Design:   gridfinity-rebuilt-openscad (baseplate and bin generator)
Author:   Kenneth Hodson (kennetek), based on Gridfinity by Zack Freedman
Source:   https://github.com/kennetek/gridfinity-rebuilt-openscad
Licence:  MIT License, https://opensource.org/licenses/MIT
          The full licence text, with both copyright notices, is in LICENSE.txt.

Changes by CadFlow: generated this baseplate and bin set with the generator
(release 2.0.0, run in OpenSCAD 2021.01; we made three small syntax edits in
gridfinity-rebuilt-bins.scad and src/helpers/grid_element.scad so that this
older OpenSCAD could run it, without changing the geometry) and exported the
pieces as STL. The instructions are our own.
