Tools

Gear generator

Spur gears with true involute teeth, and the gear they drive. Set the teeth, watch them turn, and download STL to print, or SVG and DXF to cut. Free, in your browser.

rpm
mm
mm
More settings
mm
Pressure angle

Gears only mesh with gears of the same pressure angle. 20° is the standard today; 14.5° is found on older inch gears; 25° makes stronger teeth.

mm

The play between the teeth, shared by the pair. 0.1 to 0.2 mm suits most 3D printers; 0 gives the exact profile.

Moves the smaller gear's teeth outwards, just enough that the cutter leaves their roots whole, and the larger gear's in by as much, so the centre distance stays the same.

Bore shape
mm
mm
mm

Bevels the teeth's edges on both faces. On a 3D print it keeps the first layers' squash (elephant's foot) off the teeth.

Making the gears…

Download

Made in your browser, in millimetres: STL to 3D print, SVG and DXF of the outline to laser cut or mill.

ZIP
spur-gears-m2-z20-z40.zip

In the ZIP

    How gears fit together

    Each tooth is cut the way a gear shop cuts it, so what you download is a true involute gear. Six pictures for the numbers; more in the bolt, filament and cutting service guides.

    outsidepitchrootπ × m
    Module sets the size of the teeth. Pitch diameter d = m × z; the teeth reach one module above it and 1.25 below.
    a = m × (z1 + z2) / 2
    Centre distance. The pitch circles touch, so a = m × (z1 + z2) / 2: module 2 with 20 and 40 teeth is 60 mm apart.
    3×1×
    Ratio. 12 teeth driving 36 is 3:1. The big gear turns once for every three turns of the small one, with three times the torque.
    8 teeth, undercutwith profile shift x = 0.53
    Undercut. Below about 17 teeth the cutter eats into the root of each tooth. Profile shift moves the teeth out and keeps them whole.
    flat: strongstanding: weak
    Print gears flat. Lying down, every layer holds whole teeth. Standing up, each tooth is a stack of layers that splits under load.
    Backlash is the gap between meshing teeth. Give 3D prints 0.1 to 0.2 mm; laser-cut gears get theirs from the beam's kerf.

    Questions people ask

    Is the gear generator free?

    Yes. There's no account and nothing to install, and the files are yours to use however you like, in things you sell too. The gears are made in your browser, not on a server.

    Are the teeth true involutes?

    Yes. Each gear is made the way a gear shop cuts one: a straight-sided rack, the ISO 53 basic rack, rolls round the blank, and the tooth is what it leaves. So the flanks are exact involutes, the roots have the fillet the rack's rounded tip leaves, and a small gear gets the undercut it would really have.

    What's the difference between module and diametral pitch?

    They're the same thing said two ways. Module is millimetres of pitch diameter per tooth; diametral pitch is teeth per inch of pitch diameter. Module = 25.4 / DP, so 12 DP is module 2.117, and 10 DP is module 2.54.

    Why do my 3D printed gears jam?

    Usually for one of three reasons: no backlash, a lip on the teeth from the first layers (elephant's foot), or shafts closer together than the centre distance. Give them 0.1 to 0.2 mm of backlash and a small chamfer, and measure the distance between the shafts.

    Can it make helical, bevel, worm or internal gears?

    Not yet. It makes spur gears, the straight-cut kind that turn on parallel shafts, which are also the easiest to print and cut.

    How do I share a gear I made?

    Press Copy link, by the gears (Share, on a phone), or copy the page's address. The link holds every setting, so whoever opens it sees the same gears and can download the same files.

    The gear generator is by the team making CadFlow, where you build your project in 3D and show how it goes together.

    See how CadFlow works