Tools

Pulley system calculator

Add a pulley and the load gets lighter, but you pull more rope. Drag the hand to pull. Free, in your browser.

Pulleys
4
You pull

Print a pulley

A sheave for your rope with a seat for a bearing, and the two side plates that hold it.

STL of the sheave and the side plate (print two), and SVG and DXF of the plate to laser cut, in millimetres.

For models, light loads and teaching. Never lift people, or hang anything over them.

Why pulleys make a load lighter

Count the parts of rope that hold up the moving pulley. They share the load, so with four parts each one carries a quarter, and since it's one rope with the same tension all along, a quarter is what you pull. That count is the mechanical advantage. A fixed pulley on its own only turns the rope: you pull the whole weight, but down instead of up.

Mechanical advantage = parts holding the moving block. Force = load ÷ mechanical advantage.

If the rope you pull leaves the moving block, it holds the load too and counts one more. That's called rove to advantage. It means pulling up from above, so most hoists bring the rope down over a fixed pulley instead and give the extra part away.

Why you pull more rope

The force goes down, but the rope runs further. To lift the load 1 m, each of the four parts must get 1 m shorter, so 4 m of rope passes through your hands. Force times distance is the work, and it stays the same: a pulley system never saves work, it spreads it over more rope. With friction, you put in a little more than you get out.

Rope pulled = mechanical advantage × lift height.

Friction

Each pulley takes some of the force, as the rope bends round it and its axle turns. A pulley passes on a share of the tension, its efficiency, and the losses compound from one pulley to the next. Rope Lab measured ball-bearing pulleys at 85 to 90% and bushed ones at 65 to 80%; Rigging Lab Academy puts them at about 90% and 70%, and CMC a carabiner used as a pulley at about 50%.

So the pull you need is the load divided by the sum of what reaches each part. Pulling down off the last fixed pulley, with n parts and pulleys of efficiency e, that's F = W ÷ (e + e² + … + eⁿ). With 85% pulleys a 3:1 Z-drag gives 2.57:1, as CMC works it out. Every pulley you add gives less than the one before, and with carabiners a simple tackle never passes 1:1. A bigger sheave turns easier, as Petzl notes.

The classic setups

Sailors and riggers named them long ago. The number in brackets is the same blocks rove to advantage, pulled up from the moving block.

NamePulleysAdvantageUsed for
Single fixed pulleyOne pulley on the beam1:1A flagpole or a well: you pull down instead of lifting.
Single moving pulleyOne pulley on the load, the rope tied above2:1The physics class case: half the force, twice the rope.
Gun tackleTwo single blocks2:1 (3:1)Small lifts on a boat, a light hoist.
Luff tackleA double block and a single3:1 (4:1)Tensioning a sail's luff, a vang.
Double tackleTwo double blocks4:1 (5:1)Garage hoists for a bike or a kayak, a mainsheet.
Triple tackleTwo triple blocks6:1 (7:1)Heavier lifts in a workshop or on a farm.
Z-dragTwo pulleys and a prusik on the load's rope3:1Rope rescue: hauling a person or a boat by hand.
2:1 on a 3:1A compound: one tackle pulling another6:1Rescue and rigging, where more pull is needed from few pulleys.

Where they're used

Printing your own pulleys

The generator above makes a sheave with a groove a little wider than the rope and a seat for a skateboard bearing (608) or a smaller one, and the side plates of a block. Print the sheave flat in PETG or nylon with plenty of walls, and test the bearing's fit with a short print first; our filament guide compares the materials. The axle is a bolt through both plates, with a washer either side of the sheave.

Questions people ask

How do I work out the mechanical advantage of a pulley system?

Count the parts of rope that hold up the moving block, including the one you pull if it leaves the moving block. Four parts give 4:1: you pull a quarter of the weight, before friction. In a compound system, multiply the stages: a 2:1 pulling a 3:1 is 6:1.

Does every pulley halve the force?

Only the first moving pulley halves it. Each pulley you add after that adds one part to the count, so 2:1 becomes 3:1, then 4:1. A fixed pulley at the end only turns the rope. To keep halving, pull one 2:1 with another: that's a compound system, 4:1, then 8:1.

How much rope do I need for a block and tackle?

Every part of rope between the blocks must be as long as the lift, so a 4:1 lifting 2 m needs 8 m between the blocks, and the free end long enough to reach your hands.

How much weight does the ceiling or beam take?

When you pull down, the beam carries the load and your pull: lifting 120 kg with a 4:1, about 150 kg. When you pull up from above, it carries the load less your pull. Friction adds to both, and the blocks and rope add their own weight.

Why does my pulley system feel heavier than it should?

Friction. Each pulley passes on only part of the tension, and the losses add up from one to the next: with 90% pulleys, a 4:1 gives about 3.1:1, and with carabiners as pulleys you'd lose most of the gain. Bigger sheaves on ball bearings help most.

Can I lift a person with 3D printed pulleys?

No. Printed pulleys are for models, light loads and teaching. To lift people or anything heavy, use rated blocks and rope, with their working load marked, and follow the rules where you are.

Is the pulley system calculator free?

Yes. There's no account and nothing to install, it works in your browser, and the printable files are yours to use however you like.

The pulley system calculator is by the team making CadFlow, where you build your project in 3D and show how it goes together.

See how CadFlow works